ECE R46 PDF
April 12, 2020 | by admin
Official Journal of the European Union. EN. Only the original UN/ECE texts have legal effect under international public law. The status and date. Regulation No 46 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of devices for indirect. [ECE-R46 Uniform provisions concerning the approval of rear-view mirrors and of motor vehicles with regard to the installation of rear-view mirrors, MOD].
|Published (Last):||12 June 2016|
|PDF File Size:||8.81 Mb|
|ePub File Size:||5.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
InterRegs: Regulation No. | ECE – United Nations
In the case of camera-monitor systems, the lens shall not break during the tests described in Paragraph 6. Intended Use, Activation and Deactivation The intended use shall be mentioned within the operator’s manual.
As from June 30,Contracting Parties applying this Regulation shall grant approvals to a type of device for indirect vision only if g46 type of device meets the requirements of this Regulation as amended by the 04 series of amendments. The measurements for the luminance contrast shall be carried out according to ISO Category of vehicle c: These can be conventional mirrors, camera-monitors or other devices able to present information about the indirect field of vision to the driver.
The application for approval of a type of device for indirect vision shall be submitted by the holder of the trade name or mark or by his duly accredited representative.
Other designated seating positions: Identification of the device: Rear-view mirrors Class I The dimensions of the reflecting surface shall be such that it is possible to inscribe thereon a rectangle one side of which is 40mm and the other ‘a’ mm in length, where and “r” is the radius of curvature.
Figure 7 Field of vision of Class IV wide-angle mirrors The monitor shall render a minimum contrast under various light conditions as specified by ISO For determination of the point light source contrast factor PLSCF, evaluate the luminance profile in horizontal direction Figure 3 at the vertical centre.
Location of that marking: Uniform Provisions Concerning the Approval of: Light as a Wave light is a visible form of energy most of the energy that surrounds us is invisible this energy.
Regulation 49 – 06 series (click to expand)
As from June 30,Contracting Parties applying this Regulation shall not be obliged to accept approvals of a type of vehicle or type of rr46 for indirect vision which have not been granted in accordance with the 04 series of amendments to this Regulation. Use the following working steps for determination of the maximum mounting height: A description of the location of the camera and the monitor in the vehicle system overview.
Neutral black background The point light source lab model is an emulation of a set of vehicle passing beam headlamps at a distance of m with luminous intensity of 1,cd, in accordance to the maximum allowance of luminous intensity of a vehicle passing-beam headlamp ecd point “BR” described in Regulation No. The principal radii of curvature shall be measured at three points situated as close as possible to positions at one-third, one-half and two-thirds of the distance along the arc of the reflecting surface passing through the centre of this surface and parallel to segment b, or of the arc passing through the centre of the reflecting surface which is perpendicular to it if this arc is the longer.
As from the official date of entry into force of the 04 series of amendments to this Regulation, no Contracting Party applying this Regulation shall refuse an application for approval under this Regulation as amended by the 04 series of amendments.
Example of device for measuring the reflection factor of spherical mirrors. If the vehicle type submitted wce approval in accordance with Paragraph Installation requirements for the monitor The viewing direction of the monitor shall roughly be the same direction as the one for the main mirror. A brief description of the electronic components if any of the adjustment device: The fault conditions shall be established and maintained by the manufacturer and shall be made open for inspection by the Technical Service efe the time of the type approval.
Differences between the radii of curvature of mirrors. The approval granted in respect of a vehicle type pursuant to this Regulation may be withdrawn if the requirement laid down in Paragraph ecf The second digit is a capital letter which designates the location of the seating position in a row, as viewed in the direction of forward motion of the vehicle; the following letters shall be used: Furthermore, the field of vision display should encompass the entire monitor screen.
The value of the maximum mounting height is different for different viewing distances as the displayed object size varies with the mounting height. Languages, formats and link to OJ. Type of device for indirect vision; Name of manufacturer of camera, monitor and electronic control units.
This critical viewing distance r g46 is defined by: This derogation also applies to the attachments of mirrors attachment plates, arms, swivel joints, etc.
– Transport – UNECE
The degree of obstruction shall be measured with the sun visors folded back. Install the right and left buttock weights and then, alternately, the eight torso weights. Luminance Adjustment It shall be possible to adjust the averagee luminance of the monitor either manually or automatically eece the ambient conditions.
The provisions of this Regulation shall not prohibit the approval of a type of vehicle with regard to the mounting of devices for indirect vision pursuant to this Regulation as modified by the 03 series of amendments, if all or part of the rear-view mirrors of Classes II, IV, V, VI or VII, with which it is fitted, bear the approval mark prescribed by the 02 series of amendments of this Regulation. Determination of the critical viewing distance of the monitor.